Modbo 4 0 Installation Services
Modchips also exist for the PlayStation 2 and allow for things like playing games from other regions, playing PS1 and PS2 backups, and running homebrew applications. This blog post covers the installation of the Modbo 4.0 modchip into my SCPH-70012 PS2 slim console. Things you’ll need. An SCPH-70012 PS2 slim console. Tools to take apart the PS2 slim.
A or modchip. They are pin compatible, I bought my chip from. 30 AWG kynar insulated wire wrapping wire. A soldering iron and solder I initially installed a Modbo 4.0 chip, but ended up swapping it out for a Modbo 5.0 chip. The Modbo 5.0 chip allows booting homebrew directly off of USB flash drives, which is important since the PS2 slim doesn’t have support for an internal hard drive.
Modbo 4 Manual todo: Add video links or website links showing detailed instructions. Method 2 (Western NTSC Console playing Japanese games), Modbo 4.0 or Modbo 5.0. PS2 slim (soon to have a Modbo 4.0) PS3 slim OFW MIA -Manuals for the game(s) (remember, there's a normal sized, game manual and a large VT manual.
I’d also like to mention that I was able to install the modchip with a pretty standard 1.6mm chisel tip on my Hakko FX-888D soldering iron. In other words you don’t need a super special tip for your soldering iron.
Modbo 4.0 Diagram
You just need patience, good eyes, and a steady hand. At the time of writing this post I have installed a modchip into two different PS1 systems, two different PS2 systems, and soldered a Teensy to a PS3 slim. I’ve learned a lot along the way, so I’d like to share some tips that may help your modchip installation experience be a smoother one. Since these tips apply across a lot of posts, I’ve put them into a. Modchip installation diagram Above is an an image of the installation diagram for the Modbo 3.0 diagram for NTSC V12 PS2 slim consoles. This diagram is the same for Modbo 4.0 and Modbo 5.0 chips. If you need a diagram for another version of the PS2 just leave a comment and I’ll upload a copy for you.
After LaunchELF is booted, you can install FMCB on a memory card. If you are not using a Japanese console (last 2 digits of the model is 00), then you need to make either a cross-region (under the regular 'install' option) or the multi-installation. Ps2 mod chip installation on a ps2 slim gh-040-52 subscribe if you like it. Lets Mod a PS2 scph 7704 with a Modbo 4 - Duration: 54:40. Computer Services 2,185,445 views.
As you can see from the diagram there are a total of 21 wires that need to be soldered from the PS2 to the modchip. The chip comes with double sided tape that you use to stick it to the board. I chose to mount my modchip on top of the large chip in the middle of where all of the wires needed to go. I’d recommend finding a lower point on the board instead, since I had to cut away some of the metal shield later on to get the system put back together.
You can see an image of the board and where I mounted my modchip above. Modchip installation With the modchip mounted I soldered each wire to the board. I started with the pads to the right of the chip, and then followed a counter clockwise pattern around the modchip once I finished soldering wires to the pads. Above is an image of what my installation looked like after I finished with the pads.
I had the most trouble when it came time to solder wires to the holes, or vias, that are located under the modchip. Getting solder to stick to the holes was tricky, I’d recommend using some flux to help get the solder flowing. I inserted an image of wires attached so some of the holes above.
Modbo 4 0 Installation Services Near Me
Eventually I finished soldering all of the wires to the board, and the image above is the result. As you can see I routed four ground wires to the ground pad in the diagram.
I’d actually recommend routing the ground to whichever screw hole is closest to the modchip. It’s also a good idea to use more wires for the 3.3V line as well. Putting everything back together Once I had soldered the modchip to the board, I could put the console back together.
I started by taping over all of the points I soldered to, including most of the modchip. Taping prevents any of the connections from being shorted with the case, and also helps hold the wires in place. As I mentioned earlier, I didn’t choose the best position for mounting my modchip. I had to cut away some of the metal shielding to make room for the modchip.
Removing the shielding still resulted in a very tight fit when putting everything back together. Final thoughts I was able to install my modchip my first try in less than an hour.
I found the installation process to be more difficult than the installation of a modchip on a PS1, or soldering a Teensy to a PS3 Slim. Laser failure is a problem with V12 PS2 slim consoles, which can be prevented through various methods. From my understanding the best methods are fix, and the.
I also read that later date code V12 systems don’t have the issue. My PS2 slim is a later date code, so I’m going to see if anything bad happens, and just replace the laser if I have to. I’ll update this post if anything happens. This entry was posted in,. Bookmark the.
Hi, It's little bit late, but in the image bellow you can find correct GH-52-51 diagram. I have tested it - it works. I think you have probably made bridge around SX point - it's hardest place for soldering on that board. Don't be affraid of of the 7701 number - mine was 7704, last digit is for the region code. To Bootlegninja: the diagram you provided is very dirrerent from GH-52-51, despite it's labeling.
Don't use it for that motherboard. Hope it will works for you. Note that disk spins after sucessful power on, that doesn't actually mean that motherboard is working.